Sale!
Variable Speed Drives
ATV12HU40M3 Variable speed drive ATV12 – 4kW – 5hp – 200..240V – 3ph – with heat sink
Original price was: ₦923,273.50.₦738,618.80Current price is: ₦738,618.80. 7.5% VAT
Variable speed drive ATV12 – 4kW – 5hp – 200..240V – 3ph – with heat sink
Available on back-order
| range of product |
Altivar 12
|
|
|---|---|---|
| product or component type |
Variable speed drive
|
|
| product destination |
Asynchronous motors
|
|
| product specific application |
Simple machine
|
|
| assembly style |
With heat sink
|
|
| component name |
ATV12
|
|
| Quantity per set |
Set of 1
|
|
| EMC filter |
Without EMC filter
|
|
| built-in fan |
With
|
|
| network number of phases |
3 phases
|
|
| [Us] rated supply voltage |
200…240 V – 15…10 %
|
|
| motor power kW |
4 kW
|
|
| motor power hp |
5 hp
|
|
| communication port protocol |
Modbus
|
|
| line current |
23.8 A at 200 V
19.9 A at 240 V |
|
| speed range |
1…20
|
|
| transient overtorque |
150…170 % of nominal motor torque depending on drive rating and type of motor
|
|
| asynchronous motor control profile |
Quadratic voltage/frequency ratio
Voltage/frequency ratio (V/f) Sensorless flux vector control |
|
| IP degree of protection |
IP20 without blanking plate on upper part
|
|
| noise level |
50 dB
|
| supply frequency |
50/60 Hz +/- 5 %
|
|
|---|---|---|
| connector type |
1 RJ45 (on front face) for Modbus
|
|
| physical interface |
2-wire RS 485 for Modbus
|
|
| transmission frame |
RTU for Modbus
|
|
| transmission rate |
4800 bit/s
9600 bit/s 19200 bit/s 38400 bit/s |
|
| number of addresses |
1…247 for Modbus
|
|
| communication service |
Read holding registers (03) 29 words
Write single register (06) 29 words Write multiple registers (16) 27 words Read/write multiple registers (23) 4/4 words Read device identification (43) |
|
| prospective line Isc |
5 kA
|
|
| continuous output current |
16.7 A at 4 kHz
|
|
| maximum transient current |
25 A for 60 s
|
|
| speed drive output frequency |
0.5…400 Hz
|
|
| nominal switching frequency |
4 kHz
|
|
| switching frequency |
2…16 kHz adjustable
4…16 kHz with derating factor |
|
| braking torque |
Up to 70 % of nominal motor torque without braking resistor
|
|
| motor slip compensation |
Preset in factory
Adjustable |
|
| output voltage |
200…240 V 3 phases
|
|
| electrical connection |
Terminal, clamping capacity: 5.5 mm², AWG 10 (L1, L2, L3, U, V, W, PA, PC)
|
|
| tightening torque |
1.2 N.m
|
|
| insulation |
Electrical between power and control
|
|
| supply |
Internal supply for reference potentiometer: 5 V DC (4.75…5.25 V), <10 mA, protection type: overload and short-circuit protection
Internal supply for logic inputs: 24 V DC (20.4…28.8 V), <100 mA, protection type: overload and short-circuit protection |
|
| analogue input number |
1
|
|
| analogue input type |
Configurable current AI1 0…20 mA 250 Ohm
Configurable voltage AI1 0…10 V 30 kOhm Configurable voltage AI1 0…5 V 30 kOhm |
|
| discrete input number |
4
|
|
| discrete input type |
Programmable LI1…LI4 24 V 18…30 V
|
|
| discrete input logic |
Negative logic (sink), > 16 V (state 0), < 10 V (state 1), input impedance 3.5 kOhm
Positive logic (source), 0…< 5 V (state 0), > 11 V (state 1) |
|
| sampling duration |
20 ms, tolerance +/- 1 ms for logic input
10 ms for analogue input |
|
| linearity error |
+/- 0.3 % of maximum value for analogue input
|
|
| analogue output number |
1
|
|
| analogue output type |
AO1 software-configurable voltage: 0…10 V, impedance: 470 Ohm, resolution 8 bits
AO1 software-configurable current: 0…20 mA, impedance: 800 Ohm, resolution 8 bits |
|
| discrete output number |
2
|
|
| discrete output type |
Logic output LO+, LO-
Protected relay output R1A, R1B, R1C 1 C/O |
|
| minimum switching current |
5 mA at 24 V DC for logic relay
|
|
| maximum switching current |
2 A 250 V AC inductive cos phi = 0.4 L/R = 7 ms logic relay
2 A 30 V DC inductive cos phi = 0.4 L/R = 7 ms logic relay 3 A 250 V AC resistive cos phi = 1 L/R = 0 ms logic relay 4 A 30 V DC resistive cos phi = 1 L/R = 0 ms logic relay |
|
| acceleration and deceleration ramps |
S
U Linear from 0 to 999.9 s |
|
| braking to standstill |
By DC injection, <30 s
|
|
| protection type |
Line supply overvoltage
Line supply undervoltage Overcurrent between output phases and earth Overheating protection Short-circuit between motor phases Against input phase loss in three-phase Thermal motor protection via the drive by continuous calculation of I²t |
|
| frequency resolution |
Analog input: converter A/D, 10 bits
Display unit: 0.1 Hz |
|
| time constant |
20 ms +/- 1 ms for reference change
|
|
| marking |
CE
|
|
| operating position |
Vertical +/- 10 degree
|
|
| height |
184 mm
|
|
| width |
140 mm
|
|
| depth |
141.2 mm
|
|
| net weight |
2 kg
|
|
| specific application |
Commercial equipment
|
|
| Variable speed drive application selection |
Mixer Commercial equipment
Other application Commercial equipment Ironing Textile |
|
| motor starter type |
Variable speed drive
|
Only logged in customers who have purchased this product may leave a review.
Related products
-
Sale!
Variable Speed DrivesATV12PU15M3 Variable speed drive ATV12 – 1.5kW – 2hp – 200..240V – 3ph – on base plate
Original price was: ₦611,683.63.₦489,346.90Current price is: ₦489,346.90. 7.5% VAT Add to basket -
Sale!
Variable Speed DrivesATV12HU22M2 Variable speed drive ATV12 – 2.2kW – 3hp – 200..240V – 1ph – with heat sink
Original price was: ₦580,148.50.₦464,118.80Current price is: ₦464,118.80. 7.5% VAT Add to basket -
Sale!
Variable Speed DrivesATV12P037M2 Variable speed drive ATV12 – 0.37kW – 0.55hp – 200..240V – 1ph – with heat sink
Original price was: ₦358,664.13.₦286,931.30Current price is: ₦286,931.30. 7.5% VAT Add to basket -
Sale!
Variable Speed DrivesATV12H018M2 Variable speed drive ATV12 – 0.18kW – 0.25hp – 200..240V – 1ph
Original price was: ₦310,816.38.₦248,653.10Current price is: ₦248,653.10. 7.5% VAT Add to basket
Reviews
There are no reviews yet.