Sale!

ATV12HU15M2 Variable speed drive ATV12 – 1.5kW – 2hp – 200..240V – 1ph – with heat sink

99,960.00 {7.5% VAT on Checkout & FREE DELIVERY}

Variable speed drive ATV12 – 1.5kW – 2hp – 200..240V – 1ph – with heat sink

 

Available on back-order

SKU: ATV12HU15M2 Category: Tag:
Main
range of product
Altivar 12
product or component type
Variable speed drive
product destination
Asynchronous motors
product specific application
Simple machine
assembly style
With heat sink
component name
ATV12
quantity per set
Set of 1
EMC filter
Integrated
built-in fan
With
network number of phases
1 phase
[Us] rated supply voltage
200…240 V – 15…10 %
motor power kW
1.5 kW
motor power hp
2 hp
communication port protocol
Modbus
line current
17.8 A at 200 V
14.9 A at 240 V
speed range
1…20
transient overtorque
150…170 % of nominal motor torque depending on drive rating and type of motor
asynchronous motor control profile
Sensorless flux vector control
Quadratic voltage/frequency ratio
Voltage/frequency ratio (V/f)
IP degree of protection
IP20 without blanking plate on upper part
noise level
45 dB
Complementary
supply frequency
50/60 Hz +/- 5 %
connector type
1 RJ45 (on front face) for Modbus
physical interface
2-wire RS 485 for Modbus
transmission frame
RTU for Modbus
transmission rate
4800 bit/s
9600 bit/s
19200 bit/s
38400 bit/s
number of addresses
1…247 for Modbus
communication service
Read holding registers (03) 29 words
Write single register (06) 29 words
Write multiple registers (16) 27 words
Read/write multiple registers (23) 4/4 words
Read device identification (43)
prospective line Isc
1 kA
continuous output current
7.5 A at 4 kHz
maximum transient current
11.2 A for 60 s
speed drive output frequency
0.5…400 Hz
nominal switching frequency
4 kHz
switching frequency
2…16 kHz adjustable
4…16 kHz with derating factor
braking torque
Up to 70 % of nominal motor torque without braking resistor
motor slip compensation
Adjustable
Preset in factory
output voltage
200…240 V 3 phases
electrical connection
Terminal, clamping capacity: 5.5 mm², AWG 10 (L1, L2, L3, U, V, W, PA, PC)
tightening torque
1.2 N.m
insulation
Electrical between power and control
supply
Internal supply for reference potentiometer: 5 V DC (4.75…5.25 V), <10 mA, protection type: overload and short-circuit protection
Internal supply for logic inputs: 24 V DC (20.4…28.8 V), <100 mA, protection type: overload and short-circuit protection
analogue input number
1
analogue input type
Configurable current AI1 0…20 mA 250 Ohm
Configurable voltage AI1 0…10 V 30 kOhm
Configurable voltage AI1 0…5 V 30 kOhm
discrete input number
4
discrete input type
Programmable LI1…LI4 24 V 18…30 V
discrete input logic
Negative logic (sink), > 16 V (state 0), < 10 V (state 1), input impedance 3.5 kOhm
Positive logic (source), 0…< 5 V (state 0), > 11 V (state 1)
sampling duration
20 ms, tolerance +/- 1 ms for logic input
10 ms for analogue input
linearity error
+/- 0.3 % of maximum value for analogue input
analogue output number
1
analogue output type
AO1 software-configurable voltage: 0…10 V, impedance: 470 Ohm, resolution 8 bits
AO1 software-configurable current: 0…20 mA, impedance: 800 Ohm, resolution 8 bits
discrete output number
2
discrete output type
Logic output LO+, LO-
Protected relay output R1A, R1B, R1C 1 C/O
minimum switching current
5 mA at 24 V DC for logic relay
maximum switching current
2 A 250 V AC inductive cos phi = 0.4 L/R = 7 ms logic relay
2 A 30 V DC inductive cos phi = 0.4 L/R = 7 ms logic relay
3 A 250 V AC resistive cos phi = 1 L/R = 0 ms logic relay
4 A 30 V DC resistive cos phi = 1 L/R = 0 ms logic relay
acceleration and deceleration ramps
U
S
Linear from 0 to 999.9 s
braking to standstill
By DC injection, <30 s
protection type
Line supply overvoltage
Line supply undervoltage
Overcurrent between output phases and earth
Overheating protection
Short-circuit between motor phases
Against input phase loss in three-phase
Thermal motor protection via the drive by continuous calculation of I²t
frequency resolution
Analog input: converter A/D, 10 bits
Display unit: 0.1 Hz
time constant
20 ms +/- 1 ms for reference change
marking
CE
operating position
Vertical +/- 10 degree
height
142 mm
width
105 mm
depth
156.2 mm
net weight
1.4 kg
functionality
Basic
specific application
Commercial equipment
Variable speed drive application selection
Mixer Commercial equipment
Other application Commercial equipment
Ironing Textile
motor starter type
Variable speed drive

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.