ATV310HD11N4E Variable speed drive ATV310, 11 kW, 15 hp, 380…460 V, 3 phase

Original price was: ₦598,121.00.Current price is: ₦455,147.00. 7.5% VAT

Variable speed drive ATV310, 11 kW, 15 hp, 380…460 V, 3 phase

SKU: ATV310HD11N4E Category:
range of product
Easy Altivar 310
product or component type
Variable speed drive
product specific application
Simple machine
assembly style
With heat sink
device short name
network number of phases
Three phase
[Us] rated supply voltage
380…460 V – 15…10 %
motor power kW
11 kW
motor power hp
15 hp
noise level
50 dB
product destination
Asynchronous motors
Quantity per set
Set of 1
EMC filter
Without EMC filter
type of cooling
Integrated fan
supply frequency
50/60 Hz +/- 5 %
communication port protocol
connector type
RJ45 (on front face) for Modbus
physical interface
2-wire RS 485 for Modbus
transmission frame
RTU for Modbus
transmission rate
4800 bit/s
9600 bit/s
19200 bit/s
38400 bit/s
number of addresses
1…247 for Modbus
communication service
Read holding registers (03) 29 words
Write single register (06) 29 words
Write multiple registers (16) 27 words
Read/write multiple registers (23) 4/4 words
Read device identification (43)
line current
30.4 A
apparent power
24.2 kVA
prospective line Isc
5 kA
continuous output current
24 A at 4 kHz
maximum transient current
36 A for 60 s
power dissipation in W
294.7 W at In
speed drive output frequency
0.5…400 Hz
nominal switching frequency
4 kHz
switching frequency
2…12 kHz adjustable
speed range
transient overtorque
170…200 % of nominal motor torque depending on drive rating and type of motor
braking torque
Up to 150 % of nominal motor torque with braking resistor at high inertia
Up to 70 % of nominal motor torque without braking resistor
asynchronous motor control profile
Quadratic voltage/frequency ratio
Sensorless flux vector control
Energy saving ratio
motor slip compensation
Preset in factory
Preset in factory
output voltage
380…460 V three phase
electrical connection
Terminal, clamping capacity: 10 mm² (L1, L2, L3, PA/+, PB, U, V, W)
tightening torque
2.2…2.4 N.m
Electrical between power and control
Internal supply for reference potentiometer: 5 V (4.75…5.25 V)DC, <10 mA with overload and short-circuit protection
Internal supply for logic inputs: 24 V (20.4…28.8 V)DC, <100 mA with overload and short-circuit protection
analogue input number
analogue input type
Configurable current AI1 0…20 mA 250 Ohm
Configurable voltage AI1 0…10 V 30 kOhm
Configurable voltage AI1 0…5 V 30 kOhm
discrete input number
discrete input type
Programmable LI1…LI4 24 V 18…30 V
discrete input logic
Negative logic (sink), > 16 V (state 0), < 10 V (state 1), input impedance 3.5 kOhm
Positive logic (source), 0…< 5 V (state 0), > 11 V (state 1)
sampling duration
10 ms for analogue input
20 ms, tolerance +/- 1 ms for logic input
linearity error
+/- 0.3 % of maximum value for analogue input
analogue output number
analogue output type
AO1 software-configurable voltage: 0…10 V, impedance: 470 Ohm, resolution 8 bits
AO1 software-configurable current: 0…20 mA, impedance: 800 Ohm, resolution 8 bits
discrete output number
discrete output type
Logic output LO+, LO-
Protected relay output R1A, R1B, R1C 1 C/O
minimum switching current
5 mA at 24 V DC for logic relay
maximum switching current
2 A at 250 V AC on inductive load cos phi = 0.4 L/R = 7 ms for logic relay
2 A at 30 V DC on inductive load cos phi = 0.4 L/R = 7 ms for logic relay
3 A at 250 V AC on resistive load cos phi = 1 L/R = 0 ms for logic relay
4 A at 30 V DC on resistive load cos phi = 1 L/R = 0 ms for logic relay
acceleration and deceleration ramps
braking to standstill
By DC injection, <30 s
protection type
Line supply overvoltage
Line supply undervoltage
Overcurrent between output phases and earth
Overheating protection
Short-circuit between motor phases
Against input phase loss in three-phase
Thermal motor protection via the drive by continuous calculation of I²t
frequency resolution
Analog input: converter A/D, 10 bits
Display unit: 0.1 Hz
time constant
20 ms +/- 1 ms for reference change
operating position
Vertical +/- 10 degree
171 mm
150 mm
232 mm
net weight
3.7 kg


There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.